Buying guide

What Metal Detector Frequency Should You Choose?

Updated on · By the Metal Detector Help team

Choose frequency by target size first, then by ground. Low frequencies suit large, deep targets, mid frequencies balance coins and relics, and high frequencies suit small gold and tiny items.

On this page (12 sections)
  1. How does this metal detector frequency chart break down by target?
  2. What frequency works best for coins and silver?
  3. What frequency works best for gold nuggets and small jewelry?
  4. What frequency works best for relics, caches and deep targets?
  5. How do ground conditions change the frequency you should use?
  6. Should you choose single frequency or multi frequency?
  7. What frequency works best on beaches and in wet sand?
  8. How do you pick the right type of metal detector for your frequency?
  9. What are the best high frequency options for small targets?
  10. How should you set frequency, sensitivity and ground balance?
  11. What is the fastest way to decide from the chart?
  12. The bottom line on frequency choice

Choose frequency by target size first, then by ground. Low frequencies suit large, deep targets, mid frequencies balance coins and relics, and high frequencies suit small gold and tiny items.

The metal detector frequency chart below turns that rule into bands you can use in the field.

Frequency is the tone your detector sends into the ground, measured in kilohertz, or kHz. Lower kHz tends to reach larger metal deeper.

Higher kHz tends to react more to small metal near the surface.

You also need to know what you plan to find before you pick a machine. Our guide to What Can You Find With a Metal Detector? helps you match likely targets to a frequency band.

How does this metal detector frequency chart break down by target?

Use target size as the first filter, because frequency reacts differently to small and large metal. Small targets need higher frequency, and large targets can use lower frequency for depth.

BandTypical useStrengthTrade-off
Low, about 3 to 6 kHzLarge relics, deep silver, cache huntingBetter depth on big targetsWeaker on small gold and thin foil
Mid, about 7 to 15 kHzCoins, jewelry, general park huntingBalanced depth and sensitivityLess sharp on tiny nuggets
High, about 18 to 30 kHzSmall gold, tiny jewelry, micro targetsStrong response to small metalShallower on large, deep items
Multi frequencyMixed targets and changing groundUses several bands at onceHigher price and more settings to learn

Treat these bands as starting points, not hard limits. Coil size, soil minerals and target shape can shift the best choice by one band.

Ground conditions come second. Wet salt sand, iron-rich soil and hot rocks can make a high setting noisy.

Dropping one band often gives a steadier signal even if you lose a little sensitivity.

Rule: pick the band for the smallest target you care about, then drop a band if the ground keeps you from hunting calmly.

How target shape changes the response

A flat coin, a thin ring and a round nugget of the same weight do not sound the same. Flat and thin targets often need more sensitivity, so they favor the higher side of their size band.

A round gold nugget can be hard at low frequency, which is why prospectors lean high even when the nugget is not tiny. Large iron can register well at low frequency, but you will dig more iron with it.

What frequency works best for coins and silver?

Mid frequency is the coin hunter's sweet spot. Silver coins are small enough to need sensitivity, but large enough to give depth at mid kHz.

Many park hunters start near 10 kHz for coins. The Garrett ACE 400 runs at 10 kHz, which sits in this middle range for general coin work.

The ACE 400 bundle includes a Pro-Pointer II, a carry case and a searchcoil cover. Digital target ID uses a 0 to 99 scale to help you sort conductivity before you dig.

Iron audio lets you hear iron trash while you hunt. That helps you skip bottle caps and washers in trashy areas, though you should still dig signals that sound mixed.

If coins are your main goal, our guide on the best metal detector frequency for coins adds depth on discrimination and soil settings.

Rule: for coin hunting, start in the mid band and use tone and ID to filter trash rather than chasing the highest kHz.

How to set mid frequency for a trashy park

Trashy parks reward a steady sweep and careful listening. Raise the coil over tall grass, then lower it for a clean test pass over a signal.

Use discrimination to limit common trash, but do not notch too much. You can notch out a silver coin if your settings are too tight.

Ground balance also matters in mineral soil.

What frequency works best for gold nuggets and small jewelry?

High frequency is the gold hunter's first choice. Small nuggets give a weak signal at low kHz, so you need more sensitivity to hear them at all.

Thin gold jewelry follows the same logic. A small chain or a thin ring can sound faint, and a higher band brings that signal forward.

High frequency also has a cost. It gives less depth on large targets and it can react more to hot rocks and mineral ground.

You trade depth for sensitivity.

The Garrett Pro-Pointer AT is submersible to 20 ft and has a bright orange case for visibility. It has one-button control, a fast retune feature and 3 sensitivity levels for small targets.

A pinpointer does not replace your main detector. It helps you narrow the dig hole once a high frequency signal tells you small gold is near.

Rule: choose high frequency when small gold is the hunt, and accept shallower depth on large metal.

How to hunt small gold without chasing mineral noise

Slow your sweep when you hunt for nuggets. Fast sweeps can make faint high frequency signals hard to repeat.

Use ground balance that suits your soil. If the detector chatters on hot rocks, lower sensitivity a step rather than raising frequency further.

Dig every repeatable signal in gold country.

What frequency works best for relics, caches and deep targets?

Low frequency favors large and deep metal. Big relics, cache boxes and large silver items can give a strong signal that still reaches depth at lower kHz.

Relic hunters also care about ground stability. Deep signals need a calm detector, so a lower band that runs quiet can beat a higher band that chatters.

This is where a single frequency machine can still shine. If you hunt one relic field with known targets, a dedicated low setting is simple and effective.

The Bounty Hunter TK4 Tracker IV has an 8 inch waterproof coil and 3 detection modes. It is battery powered, lightweight at 1270 g and made for adults and kids.

Its 3 modes are all-metal, tone and discrimination. You can switch modes to filter trash or to hear every signal in all-metal mode.

Rule: choose low frequency for large, deep relics, and value a quiet signal over raw sensitivity.

When deep hunting needs a different coil and pace

A larger coil can help with depth, but it also covers more ground per sweep. That wider coverage can make pinpointing harder in trash.

Slow pace helps on deep targets. A steady sweep gives you time to hear a faint edge, and a second pass from another angle helps judge depth before you dig.

How do ground conditions change the frequency you should use?

Ground is the second half of the chart. Salt water, wet sand, iron soil and mineral ground can all change which band works best on a given day.

Wet beach sand is the classic example. Salt water is conductive, so a detector can chatter or lose depth.

Many beach hunters drop frequency, use ground balance or switch to a multi frequency option.

Mineral soil is another common problem. Hot rocks and iron-rich dirt make high frequencies noisy.

A lower band or lower sensitivity often restores a usable hunt.

Dry, mild soil is the easiest case. You can run the band that matches your target and keep sensitivity high.

Rule: if the ground makes your chosen band noisy, drop one band or lower sensitivity before you blame the target.

How to test a band in the first 10 minutes

Walk a short test strip before you commit to a full hunt. Sweep at your normal height and listen for chatter, nulls and false signals.

Try your chosen band, then try one band lower. Keep the same sweep speed and coil height so the comparison is fair.

Pick the setting with the cleanest repeatable signals.

Should you choose single frequency or multi frequency?

Single frequency gives you one band to learn well. It is simpler, often lighter and often a better value for a focused hunt.

Multi frequency uses several bands at once. It can handle mixed targets and changing ground in one sweep, which helps on beaches and in parks where soil shifts.

The choice comes down to how much your ground and targets change. If you hunt one type of site, single frequency is enough.

If you hunt beaches, parks and fields in one week, multi frequency saves you from switching machines.

Our comparison of multi frequency vs single metal detectors walks through cost and learning time. If you want current multi options, see our best multi frequency metal detector picks.

Rule: pick single frequency for a focused hunt, and multi frequency for mixed sites and changing ground.

Which is easier for a beginner to learn?

Single frequency is easier to learn because you focus on one band and a few controls. Multi frequency adds modes and settings, which helps in tough ground but takes more practice.

Beginners who hunt mostly yards and parks can start single frequency and add multi later. Beginners who hunt wet beaches from day one should look at multi sooner.

What frequency works best on beaches and in wet sand?

Wet sand and salt water call for stability first. A mid or low band with good ground balance often beats a high band that keeps chattering.

Multi frequency machines are popular on beaches because they can balance salt ground and still hear small jewelry. That balance is the main reason to pay more for multi.

A waterproof coil helps, but frequency still matters. The TK4 has an 8 inch waterproof coil for shallow water and damp soil.

That coil suits beach and backyard hunting where you may wade or hunt wet sand.

Do not use high frequency as your only beach setting. Small jewelry is a high frequency target, but wet sand can make that band noisy.

Test both bands in the wet zone and the dry zone.

Rule: on wet beaches, choose the band that stays quiet in salt ground, even if it is not the band for tiny gold.

How to sweep wet sand for jewelry

Keep your coil low but steady over wet sand. A bouncing coil changes the signal and makes small jewelry sound like trash.

Hunt in a grid and overlap your passes. Small jewelry can sit shallow, and a clean overlap helps you hear a faint edge signal.

Dig all repeatable high tones in the wet zone.

How do you pick the right type of metal detector for your frequency?

Frequency choice starts with detector type. A coin machine, a gold machine and a relic machine are tuned for different bands and different controls.

Start with the hunt you will do most. If you hunt parks for coins, a mid frequency coin machine fits.

If you hunt gold country, a high frequency gold machine fits.

Our guide on the type of metal detector helps you sort coin, gold, relic and multi purpose machines. Read it before you shop, because type locks in frequency options.

You should also check what a detector is actually for. Our overview of [What Is a Metal Detector Used For?

The Basics](/what-is-a-metal-detector-used-for/) covers coin, jewelry, relic and prospecting uses in plain terms.

Rule: choose detector type for your main hunt, then choose frequency inside that type.

How to match type to frequency without overspending

List your top two hunts before you shop. A coin hunter who also wants gold may need multi frequency or two machines.

If your top hunt is clear, buy for that hunt. Do not buy high frequency alone for relic hunting, or low frequency alone for nuggets.

The band must match the target.

What are the best high frequency options for small targets?

High frequency picks focus on small gold, tiny jewelry and micro targets. Look for ground balance, stable audio and a coil that suits your soil.

Our best high frequency metal detectors list is the place to compare those options by target and ground. Use it when small gold is your main goal.

Check sensitivity controls before you buy. High frequency without good ground balance can be noisy in mineral soil.

A machine that lets you lower sensitivity in small steps will hunt more sites.

Check coil size too. A smaller coil helps in trash and hot rocks.

A larger coil covers more ground but can make pinpointing harder.

Rule: for small targets, buy high frequency with ground balance and fine sensitivity control, not high frequency alone.

How to choose a high frequency machine for nuggets

Nugget hunters need clean audio. A faint nugget signal must stand out from ground noise, or you will miss it on the sweep.

Look for a fast retune or ground balance feature. That helps when you cross from mild soil to hot rocks during one hunt.

A pinpointer with high sensitivity helps you recover what the main detector finds. The Pro-Pointer AT has 3 sensitivity levels and a 20 ft waterproof build for wet areas.

How should you set frequency, sensitivity and ground balance?

Set frequency for the target, then set ground balance for the soil, then set sensitivity for the day. That order keeps your choices logical.

Start with ground balance on clean soil. Pump the coil up and down, then adjust until the detector runs quiet.

Do not balance over a target or a trashy patch.

Raise sensitivity until the detector starts to chatter, then back off one notch. That gives you the most sensitivity you can use without false signals.

Test with a known target if you can. A small coin or a test piece can show you whether your settings still hear small metal.

Rule: set band for target, balance for ground, then sensitivity for the day, in that order.

Common setting mistakes to avoid

Do not run maximum sensitivity in noisy ground. A chattering detector hides real signals and tires you out.

Do not balance over metal. A bad balance makes the detector less stable and less sensitive to real targets.

Do not change settings without a test sweep.

What is the fastest way to decide from the chart?

Use this chart as a quick decision tool before you buy or before you hunt. Start with the smallest target you want, then check the ground.

If you huntStart withWatch for
Silver coins in parksMid bandTrash and mineral soil
Small gold nuggetsHigh bandHot rocks and noisy ground
Large relics and cachesLow bandIron trash at depth
Wet beach jewelryMid band or multiSalt ground chatter
Mixed targets, mixed sitesMulti frequencyPrice and learning curve

Write your top hunt on a card and tape it to the case. That one line will keep you from buying a band that does not fit your hunt.

Ask one question before you pay. Will this band work on the ground where you will actually hunt?

If the answer is no, change the band or the machine type.

Rule: decide by smallest target, then ground, then budget, and buy the band that fits all three.

The bottom line on frequency choice

Pick the band for the smallest target you want, then drop a band if the ground is noisy. That one rule works for coins, gold, relics and beach jewelry.

Pick single frequency for a focused hunt and multi frequency for mixed sites. Pick high frequency for nuggets, mid for coins and low for large relics.

Use this metal detector frequency chart before you buy, then test your settings in the first 10 minutes of each hunt. A clean signal on the right band will find more than a noisy signal on the wrong band.

Frequently asked questions

How do I read a metal detector frequency chart?

Match target size to the band, then adjust for ground. Small gold and tiny foil sit at the high end, coins sit in the middle, and large relics sit lower.

Wet or mineral ground can force you one band lower for stability.

What frequency is best for coins?

Mid frequencies around the coin band give a good mix of depth and sensitivity to small silver. You can hunt coins on a single frequency machine if you mainly hunt parks and yards.

A multi frequency option helps when ground changes during one hunt.

What frequency is best for gold nuggets?

High frequency suits small nuggets because it reacts more to tiny conductive targets. A pinpointer with high sensitivity also helps you recover small pieces once the main detector signals.

Wet beach sand may need a lower setting or ground balance to stay quiet.

Does higher frequency always mean shallower depth?

Higher frequency often trades some depth on large targets for more sensitivity to small ones. The loss matters most on large, deep relics and quiet ground.

On small gold, the gain in sensitivity is worth more than the depth you give up.